Mechanical Department is well equipped with Laboratories which provides research facilities for students and faculties. The laboratory contains research equipment which helps to perform experimental research and software helps to perform simulation and modeling.

• Experimental Stress Analysis Lab
• Noise and Vibration Lab
• Tribology Lab
• Material Science Lab
• Modeling and Simulation
• Heat power and I.C. Engine

Noise and Vibration Lab
Sr. No.	Name of Equipment	Utility
1.	Electrodynamic Shaker 0 – 10kHz	To excite the structure for dynamic analysis.
3.	FFT Analyzer with Accessories Frequency Range 1Hz to 20kHz	To determine natural frequency and used for fault diagnosis.
4.	Hand Held Vibration Meter Frequency Range 0.2 Hz to 10 kHz Acceleration 0.1 to 240 m/s^2	To measure overall vibration level and condition monitoring measurements.
6.	Sound Level Meter	To measure sound pressure level (SPL)
FFT Analyzer		Hand Held Vibrometer	Electrodynamic Shaker

Material Science Lab
Sr. No.	Name Equipment		Utility
1	Magnetic Particle Testing		Non-destructive  testing of ferromagnetic material
2	Ultrasonic Testing		Non-destructive testing of component
3	Micro-Vickers hardness Testing		To check the hardness of the material
4	Optical emission spectrometer		This equipment is useful to determine the elemental composition of ferrous alloys, aluminum alloys and copper alloys.
5	Image analyzer system consisting of microscope, image acquisition camera, and image analysis software.		This equipment is useful for  Examination of micro structure of ferrous & nonferrous metals to determine the phases present and their amount, grain structure To measure nodularity and inclusion count and check for porosity, measure amount of graphite flakes etc.
6	Digital Rockwell Hardness Tester		To check the hardness of the material on different Rockwell scales.
Optical emission spectrometer			Image Analyzer
Micro Vickers Hardness Testing			Ultrasonic Testing Machine
Magnetic Particle Testing			Digital Rockwell Hardness Tester

Heat Power and I.C. Engine Lab

I.C. Engine Lab
Sr. No.	Name of Equipment		Utility
1.	Test Rig of base and alternative fuel		Testing of 1.Computer controlled variable compression ration engine 2.Multi-cylinder petrol engine 3.Single cylinder diesel engine
2.	Combustion Analyzer   Make: DEWE-RACK-4, DEWE-BOX-CA-EDUC, CA-OPT1, CA-ANGLE-SENSOR-0.2, CA-OPT3		To measure 1. Crank angle based pressure diagram 2. Integrated pressure signal 3. Pressure / Volume diagram 4. Calculated heating process 5. On-line knocking recognition 6. Mathematic Setting 7. Statistical display 8. Data storing and data export to ASCII
3.	Two Wheeler Chassis Dynamometer Make: ATE, Maxi. 100 HP at 3000 / 6000 rpm Volumetric Fuel consumption Measurement Unit		Braked Type Chassis Dynamometer Performance Tests 1) Normal Mode Test 2) Acceleration Test 3) Braking Test 4) Average Test Plotting Performance Characteristics Curves- a. Vehicle speed v/s HP in different gears b. Vehicle speed v/s torques in different gears c. Vehicle speed v/s tractive effort
4.	Eddy Current Dynamometer Make : SAJ Power rating : 80 kW @ 4800 - 9000 rpm		Engine Brake Power, Torque, Specific Fuel Consumption, Air Consumption, Mechanical Efficiency, Thermal Efficiency, Friction Power, Indicated Power
5.	Microprocessor Based four Gases Auto. Exhaust Analyzer		Exhaust Emission Measurement of CO, HC, CO2, O2 (Petrol Engine)CO : 0-9.9 % resolution 0.1% HC : 0-9990 ppm Resolution 10 ppm CO2 : 0 - 19.9 Resolution 0.1 % O2 : 0 - 25 % Resolution: 0.1 % Response time : 10 second Warm up time: 20 min. Power Supply : 230V AC
6.	Smoke Meter		Exhaust Emission Measurement of Diesel engines Smoke (Diesel Engine) Display indication : light absorption coefficient (k) /% Opacity Warm up time : 15 min. Power requirement : 230 V Display range : 0-9.9 per meter
7.	Engine Scanner		Engine diagnostics tool (Petrol Engine) Computer controlled system engine analyzer with diesel interface, 80-column printer
8.	KAL Equipment		Air / Fuel ratio measurement and CO measurement (Petrol Engine)A/F ratio 8 :1 to 16: (Gasoline) A/F ratio 12 :1 to 16 : 1 (Liquid Gas)
Heat Power Lab
1		Sonicator	Sonication applies sound energy to agitate particles in a sample solution which can produce nano-emulsion, nano-crystals, liposomes and max emulsions also for waste water purification.
2		Calorific value Measurement	Instrument helps to measure calorific value measurement of fuel
3		Rheometer	Measurement of fuel viscosity
4		Wind tunnel	It is used for measurement of aerodynamic characteristics of object. Using wind tunnel model we can measure aerodynamic forces, pressure distribution etc.
Sonicator			Wind Tunnel

Other Lab Equipment
Sr. No.	Name of the Equipment	Utility
1.	Rheometer	It is used to measure a liquid’s suspensions or slurries flow when force is applied to it. Many fluids can be tested with a rheometer when a single numerical viscosity value cannot determine them due to their components. The rheometer tests a fluid’s rheology. Characterization of Newtonian and Non-Newtonian fluids using Modular Compact Rheometer MCR-52
2.	3D Printing	It helps to create 3D model using additive manufacturing process
3D Printing Machine			Rheometer